John Deere H310 NSL

Double tap to zoom

 

Features

Boom lockout for easy service

A hydraulic shut-off valve is included with the H-Series Ag Loaders to ensure the loader does not lower suddenly. For example, this allows the boom to be locked out when someone is required to be located under the loader boom for service work on the tractor. It should not be used for extended periods of time unless an appropriate support stand is also utilized.

Concealed oil lines improve appearance and reduce damage

Over time, increased width in tractor hoods have caused issues with available space for running traditional oil lines of a loader along the boom, making them more susceptible to damage. 

To improve this situation, the oil lines have been routed through the boom arm and the torque tube, improving line protection and the appearance of the loader.

False rod bucket cylinders improve productivity

Fast bucket cycle times are important to dump the load from the bucket as quickly as possible, (quite often) in order to be as productive as possible, while completing loading operations. The bucket cylinder design can have a major impact on this cycle time, especially for the mechanical self-leveling loaders. 

Therefore, all MSL H-Series Loaders utilize false rod bucket cylinders. A false rod cylinder has a smaller displacement of oil requirement on the head end of the cylinder, which allows this cylinder to dump much faster than a normal cylinder.

Single-point hydraulic connection saves time

The H240, H260, and H310 Loaders can be ordered with a single-point hydraulic connection that also incorporates the connection point for any electrical needs. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

Loader removal (parking) made easy

John Deere loaders are easily removed and reinstalled on tractors without tools. The parking system allows removing or attaching the loader to the tractor in minutes without the need for tools.

To remove or park the loader, apply slight down pressure to the loader boom with the bucket dumped at approximately a 30-degree angle. With the tractor in park, lower the parking stands and place the mast pins in the open position.

Utilizing the boom circuit with the tractor in neutral, rotate the mast forward until the mast has rotated past the pin location on the mounting frame by extending the lift cylinder. Now using the bucket circuit, roll back the bucket until the mast is removed from the pocket and will clear the tires.

With the tractor in park, shut the engine off and relieve the hydraulic pressure as indicated for the tractor (rotating the joystick). Disconnect or open the single-point hydraulic connector (or remove couplers if no single point is installed).

Store the loader half of the single-point connector or hoses, and back away from the loader.

Specifications

TRACTOR ---
Model 6105R/6115R/6125R
Front tire 16.9R24
Rear tire Rear tire
Front axle configuration MFWD w/ Limited Slip Differential
Wheelbase 2580 mm (101.6 in.)
Pump capacity 114 L/min (30.1 gpm)
Rated pressure 2901 psi (200 bar)
LOADER ---
Leveling configuration Mechanical Self Leveling (MSL)
Bucket used Materials 73 in. (Materials 1850 mm)
Bucket weight 503 lb (228 kg)
Lift capacity at full height Measured at pivot (U) 3746 lb (1699 kg); Measured at 800 mm ahead of pivot (V) 1846 kg (4070 lb)
Lift capacity at 59 in. (1500 mm) Measured at pivot (W) 2187 kg (4822 lb); Measured at 800 mm ahead of pivot (X) 2090 kg (4608 lb)
Boom breakout force Measured at pivot (Y) 2677 kgf (5902 lbf); Measured at 800 mm ahead of pivot (Z) 2335 kgf (5148 lbf)
Bucket rollback force capacity At maximum height (VV) 1513 kgf (3336 lbf); At 59-in. (1500-mm) lift height (XX) 3003 kgf (6620 lbf); At ground-level line (ZZ) 3059 kgf (6744 lbf)
Dimensions Maximum lift height (A) 3855 mm (151.8 in.); At full height - bucket level(B) 3661 mm (144.1 in.); At full height - bucket dumped (C) 2826 mm (111.3 in.) 
Overall length (I+F), ft (m) 5 m (16.4 ft)
Overall height in carry position (J) ---
Digging depth (H) 31 mm (1.2 in.)
Reach At maximum height (D) 800 mm (31.5 in.); At ground level - bucket level (F) 2422 mm (95.4 in.)
Bucket angle Dump angle, degrees (E) -7 degree (angle); Rollback angle, degrees (G) 42 degree (angle); Dump angle, ground -95 degree (angle)
Cycle times Loader raise, seconds 2.3 seconds; Loader lower, seconds 1.9 seconds; Bucket dump, seconds 1.4 seconds; Bucket rollback, seconds 1.4 seconds